
Stoddard Filter Elements are designed for easy replacement to keep your system running cleanly and efficiently. Custom blower filter elements with different dimensions or filtration levels are available on request as well.
Replacement Cartridge Filters

Paper Element (Standard)
- Moisture-resistant pleated paper media in plastisol end caps with expanded metal on ID and OD for strength.
- Efficiency: 99% on 1 micron particles and larger.
- Service: Clean by directing compressed air through filter in apposite direction of air flow (DO NOT WASH), EVENTUALLY ELEMENT WILL NEED TO BE REPLACED.
- F64/F65 Housing Size
- 1″ – 2.5″
- 3″ – 5″
- 6″
- 8″
- 10″ – 14″
- Part Number
- F8-108
- F8-109
- F8-110
- F8-111
- F8-137

Felt Media Element
- Washable pleated felt media in plastisol end caps between layers of screen mesh.
- Efficiency: 98% on 3 micron particles and larger.
- Service: Rap out excessive dirt and wash in warm water with mild detergent. Rinse thoroughly and rap out excessive water before reinstalling.
- F64/F65 Housing Size
- 1″ – 2.5″
- 3″ – 5″
- 6″
- 8″
- 10″ – 14″
- Part Number
- F8-151
- F8-135
- F8-134
- F8-139
- F8-148

Wire Mesh Element
- Layered epoxy coated screen wire in between plastisol end caps.
- Efficiency: 90% on 10 micron particles and larger.
- Service: Soak in hot water and detergent. After rinsing allow filter to dry. Adhesive (light oil) can then be applied at 1.5 to 2 oz./element. Allow excess adhesive to drain off prior to installing.
- F64/F65 Housing Size
- 1″ – 2.5″
- 3″ – 5″
- 6″
- 8″
- 10″ – 14″
- Part Number
- F8-129
- F8-130
- F8-131
- F8-132
- F8-142

Polyurethane Element
- Washable polyurethane media with a steel core.
- Efficiency: 98% on 10 micron particles and larger.
- Service: Remove foam element from steel center core. Wash element in warm, soapy water. Rinse thoroughly in fresh water and wring out. Install on steel center core and set aside to dry. EVENTUALLY ELEMENT WILL NEED TO BE REPLACED.
- F72/F65 Housing Size
- 1″ – 2.5″
- 3″ – 5″
- 6″
- 8″
- 10″ – 14″
- Part Number
- F8-119
- F8-120
- F8-121
- F8-122
- F8-123
Service Instructions
- Turn off air moving device prior to servicing.
- Remove wing nut on housing cover. Remove cover.
- Check elements and service as shown above for the appropriate element.
- Check inside of housing for loose articles before replacing cover.
- Replace cover.
- Restart the air moving device.
Need a replacement filter element? Contact us below:
Replacement Panel Filters

F2-106 Washable Polyester Element (Standard)
- Construction: 24˝ x 24˝ x 2˝ filter element with a washable polyester media, between a screen mesh and expanded metal grid on a galvanized metal frame.
- Efficiency: 99% on 10 micron particles and larger.
- Service: Rap out excessive dirt and wash in warm water containing a mild detergent. Rinse thoroughly and rap out excessive water. Replace in Filter Housing.

F3-101 Disposable Polyester Element
- Construction: 24˝ x 24˝ x 2˝ filter element with a disposable polyester media, held in place with a galvanized metal holding frame, designed for easy media replacement.
- Efficiency: 90% on 10 micron particles and larger.
- Service: Replace disposable media when visually dirty. Replaceable polyester media is part number A26-101.

F4-101 Pleated Paper Element
- Construction: 24˝ x 24˝ x 3˝ filter element with a pleated paper media, held in place with a metal holding frame
- Efficiency: 99% on 1 micron particles and larger.
- Service: Clean by directing compressed air through filter in opposite direction to flow. (Do Not Wash in Water).
F5-101 Molded Glass HEPA Element
- Construction: 24˝ x 24˝ x 11-1/2˝ filter element with a molded glass media bonded to a Galvaneal metal frame which has a fluid seal to eliminate bypass
- Efficiency: 99.97% on 0.3 micron and above by DOP test method.
- Service: Filter is not cleanable. If the Primary and Secondary filters are properly maintained, this filter should last 18 to 24 months.
Service Instructions
- Turn off air moving device prior to servicing.
- Remove fasteners on weatherhoods. Remove weatherhood.
- Check elements and service as shown above for the appropriate element.
- Check inside of housing for loose articles before replacing weatherhood.
- Replace weatherhood.
- Restart the air moving device.
